Applied Scientific Instruments Co., Ltd.

บริษัท แอพพลายด์ ไซแอนทิฟิค อินสตรูเม้นท์ส จํากัด

ศูนย์รวมเครื่องมือทดสอบ เครื่องมือวิทยาศาสตร์ เครื่องมือวิเคราะห์ทุกชนิด

 

ติดต่อสอบถาม

ผ่าน LINE ID

@asithailand

 

Impulse generator T3-61

หมวดหมู่สินค้า: Testing Europe
รหัส :

แท็ก: Education unituni

31 มีนาคม 2568

ผู้ชม 2 ผู้ชม

 Impulse generator T3-61

Inmtroduction

T3-61 1,2/50 IMPULSE GENERATOR is intended for performing dielectric tests with impulse voltage on low-voltage equipment. It creates impulses with a virtual front time of 1,2 µs and a virtual time to half-value of 50 µs. Samples are tested by (high) voltage surges.

It is constructed in compliance with the following standards:

IEC 60335-1: Household and similar electrical appliances – Safety – Part 1: General requirements: Clause 14 Transient overvoltages

IEC 60950-1: Information technology equipment – Safety – Part 1: General requirements: Annex N: Impulse test generators

IEC 61180-1: High-voltage test techniques for low-voltage equipment; Part 1: Definitions, test and procedure requirements

IEC 61180-2 High-voltage test techniques for low-voltage equipment - Part 2: Test equipment

We designed IMPULSE GENERATOR with the following goals:

  • Safety
  • Reliability
  • Ease of operation
  • Ergonomical design

Main Features

  • Ergonomically designed.
  • Transparent acrylic 10 mm thick door and side panels enable observing of tested sample during the test, and protection of operator in case that due to the energy released during a surge a sample bursts (small explosion)
  • Test cabinet bottom is 20 mm thick
  • Two voltage generators – separate for each polarity
  • High voltage switching systems with electromagnets for better safety
  • Two door safety protection switches – surge can only be applied when doors are closed
  • V-meter enables observing and adjusting surge voltage
  • Internal voltage divider 10:1 with outside BNC (to connect a oscilloscope with HV probe)
  • HV oscilloscope probe
  • Variable ratio transformer with knob for voltage adjustment 400 – 12 000 V DC
  • Push button CHARGE + for positive charging polarity
  • Push button CHARGE - for negative charging polarity
  • Illuminated push button DISCHARGE for activating the surge
  • Mains switch with fuse
  • Anodized aluminum front plate, with inscriptions that clearly explain the function of each component on the front plate
  • Sample connection terminal sockets are located inside insulated protecting test cabinet
  • Two port holes, with plugs, for possibility of connecting bigger samples in external test cabinets
  • Auto‑detect connector, for connecting external door (protection) switch if customer uses other/bigger external test cabinet

Technical Specication

Supplying voltage 230V, 50Hz / other optional
Power consumption 650 VA
Output voltage surge 400V-12kV, adjustable
V-meter  0-15 kV DC, 4 1/2 digit 2,5 % FS
HV oscilloscope probe max. 1500 V, 300 Mhz bandwidth, ratio 100:1
Capacitor 1µF 
Virtual impedance 12 ohms
Minimum charging time 3 seconds (as per standard request)
Waveform 1.2/50µs
BNC output 10:1
Dimensions  
Control unit WxDxH 470 x 490 x 285 mm
Test cabinet WxDxH 420 x 300 x 250 mm

 

ขอใบเสนอราคา

ดาวน์โหลดโบว์ชัวร์

 

 

Engine by shopup.com