DESCRIPTION

The Armfield S16 Hydraulic Flow Demonstrator is a free-standing accessory to the Armfield Hydraulic Bench which enables hydraulic phenomena associated with the flow of water through both open channels and closed conduits to be set up quickly, easily and visually demonstrated.

Measurements taken in each configuration permit the associated flow conditions to be analysed.

The flow channel of the S16 Hydraulic Flow Demonstrator is constructed using clear acrylic for visibility and is supported by a floor standing, metal frame fitted with castors for mobility.

The flow channel consists of an inlet tank with overflow and flow stilling arrangement, a rectangular working section and a discharge tank.

Control valves and adjustable weirs allow the flow conditions to be varied independently at the entry to and exit from the working section. The working section can be flooded to create a closed conduit or operate partially filled as an open channel.

The most important feature of this equipment is the adjustable section of the bed which, together with its transition section (ramps), may be raised or lowered using an external actuator whilst the water is still flowing. This facility affords a striking demonstration of the significance of channel critical depth. It is also used to vary the cross section for demonstration of the Bernoulli equation in closed conduit flow.

A removable panel in the roof of the working section allows models of typical hydraulic structures to be installed, namely; a sharp crested weir, broad crested weir (also used to create a culvert) and Ogee weir.

Pitot tubes and tappings connected to a multi-tube manometer allow total and static heads to be measured and compared at three locations in the working section. The height of the Pitot tubes is adjustable allowing the velocity profile to be determined at any position between the bed and the roof of the working section. Transparent scales allow all important heights and levels to be measured throughout the working section.

The S16 Hydraulic Flow Demonstrator is designed to be used in conjunction with an Armfield F1-10/F1-10-2 Hydraulics Bench, which provides a recirculating water supply and a volumetric measuring facility. The Flow Demonstrator can be used with an independent water supply of up to 1.6 litres/sec provided that water discharging from the channel can be intercepted.

An optional direct reading flowmeter is available that allows rapid adjustment to the required flow conditions.

EDUCATION CONTENT

The Armfield S16 Hydraulic Flow Demonstrator simply connects to a standard F1-10/F1-10-2 Hydraulics Bench to permit the study of the following basic aspects of fluid flow:

Open channel flow

• Flow beneath an undershot weir (sluice gate)
• Flow over sharp crested, broad crested and Ogee weirs

Using hydraulic structures to measure flow in an open channel

Effect of changes in upstream and downstream water level

Characteristics of clinging, aerated, depressed and drowned nappes

• Subcritical, critical and supercritical flow/depth

Changes in specific energy and control imposed by the minimum energy condition

• Characteristics of hydraulic jumps

Force and energy conditions in a hydraulic jump

Flow patterns associated with hydraulic jumps

Flow over drop structures/energy dissipation

• Changes in flow profile in relation to the Froude number (predicting flow conditions in an open channel)
• Observation of flow patterns associated with flow around hydraulic structures
• Velocity of gravity waves in shallow water/formation of surface waves near critical depth
• Project work – evaluation of user constructed hydraulic structures

Closed conduit flow

• Application of the Bernoulli and continuity equations to converging and diverging flow
• Effect of gradual and sudden changes in cross section (energy losses)
• Using a contraction as a flow measuring device
• Using a Pitot tube to measure velocity/velocity profile
• Flow through a culvert

TECHNICAL SPECIFICATIONS

Width of working section: 77mm

Depth of working section: 150mm

Length of working section: 1100mm

Maximum operating flow rate: 1.6 litres/sec

FEATURES & BENEFITS

• Demonstrate flow through both open channels and close conduits using this highly visual accessory to the Hydraulics Bench
• Demonstrations can be set up quickly and easily, including varying the upstream and downstream flow conditions
• I deal for student project work – user constructed models of different hydraulic structures can be evaluated
• Unique elevating bed section and models of various hydraulic structures allow the difficult concepts of critical flow and energy changes to be clearly demonstrated and analysed
• Working section large enough for the various flow phenomena to be seen clearly by a group of students – enables a teacher to provide practical demonstrations at the same time as explaining the theory

ขอใบเสนอราคา

ดาวน์โหลดโบว์ชัวร์